#UBUNTU 14.04.2 SERVER DOWNLOAD HOW TO#
#UBUNTU 14.04.2 SERVER DOWNLOAD INSTALL#
#UBUNTU 14.04.2 SERVER DOWNLOAD UPGRADE#
#UBUNTU 14.04.2 SERVER DOWNLOAD SOFTWARE#
#UBUNTU 14.04.2 SERVER DOWNLOAD PASSWORD#

Once you do the configuration, get back to the petitboot menu, and boot the entry you just configured ' User Item 1'. You do not need to fill out the other entries, if you just want to do a default installation. On this example, I used version 14.04 that I following URLs:ДЇor a more recent version, as 14.04.1, 14.04.2 and updates, check the UbuntuВ ppc64elВ wikiВ pageВ downloadВ section For Ubuntu, you should point it to the CanonicalВ UbuntuВ 14.04В netbootВ website. Once you are editing the boot entry, you should choose the ' Specify paths/URLs manually' option and you must provide the installer kernel and initird. By creating a new entry, you will go into Option Editor to configure the entry details, as shown:

Once the network is configured, you can create a new entry in the petitboot by pressing the letter ' n'.

#UBUNTU 14.04.2 SERVER DOWNLOAD INSTALL#

In order to install from the network, you need to configure the System Network in the ' System Configuration' menu entry.

#UBUNTU 14.04.2 SERVER DOWNLOAD HOW TO#

This document will explain how to install from the network.Д¤. From here, you can install an Ubuntu DVD in the machine using DVD-ROM and boot from it. Petitboot is the bootloader for the IBM Power machines configured with PowerKVM. Once the machine is booted up, you will see the petitbootВ console, as shown below: In order to exit the console, you should type ~. Once you run the last command, you will be seeing the machine console, and everything you type will be sent to the machine.

#UBUNTU 14.04.2 SERVER DOWNLOAD PASSWORD#

# ipmitool -I lanplus -H fsphostname -P password sol activate.

# ipmitool -I lanplus -H fsphostname -P password power cycle.

Once the machine is in PowerKVM mode, you need to connect to the FSP using IPMIВ to get the machine console. Turn off the server by going to the server Advanced System Management (ASM), under System ConfigurationВ в‡’ Hypervisor Configuration, and set the hypervisor mode to KVM (or OPAL) and choose a IPMI passwordДў. If you build the system with the PowerKVM configuration, you are ready to go, otherwise, you can configure it using the following steps: This step selects the OPAL Firmware to be loaded. In order to install Ubuntu 14.04 on the IBM Power system, the system needs to be set for KVM as the Hypervisor mode. These instructions assume a netboot load.ДЎ. Your system must have access to the external web for access to Canonical's netboot server - or you will need a DVD image downloaded and burned to a DVD.

#UBUNTU 14.04.2 SERVER DOWNLOAD SOFTWARE#

The PowerKVM software can be re-installed at a later time, and your guests can be re-created. These instructions replace (destroy) your existing PowerKVM installed host and all of the guests. You are over-writing your PowerKVM install. Alternatively, you can always ask a question in the Forums here on the Community! If you should encounter any problems running with the non-virtualized technical preview you can report your bugs against Ubuntu in Launchpad.

This ability is provided as a technical preview only. The ability to run Ubuntu directly on the POWER8 Linux-only system is provided as-is, is not a supported configuration option at this time, and therefore, is not for production use. In practice, OPAL firmware enables a Linux operating system to run directly on the system, and running KVM in that operating system is not a requirement. In the scenario described here in this article, there is no KVM hosting, and the Ubuntu 14.04 operating system is running as an operating system directly on the system.Д«ecause the OPAL firmware enables the PowerKVM mode, the terminology used in selecting the firmware below is targeted at that mode. By running directly on the system, this enables the operating system to be a KVM host, creating and controlling KVM Guests. The OPAL firmware referenced below is designed to allow a Linux operating system to run directly on the POWER8 system.

#UBUNTU 14.04.2 SERVER DOWNLOAD UPGRADE#

Note: If you are running Ubuntu 14.04 non-virtualized, you need to upgrade the kernel packages to get cpufreq support. Over time, this capability is available in the open-source communities, so new versions of other Linux distros are expected to be enabled for this support as well. There is no PowerVM LPAR layer, and there is no PowerKVM hosting layer. It is also possible to run Ubuntu 14.04 directly on these systems, which the development teams refer to as non-virtualized mode, or 'bare-metal'. Ubuntu 14.04 is generally available today and fully supported as a PowerKVM guest on the IBM Power Systems shown below:ДЇor more details on Ubuntu 14.04 - see Canonical's WhatвЂ™sВ newВ inВ 14.04В LTS document. We show how Ubuntu can be installed directly on the OPAL firmware, and run as a single-image operating system directly on the system. This technical preview tutorial explains how users of IBM's latest POWER8-based scale-out Linux servers can try Ubuntu running non-virtualized.

Ubuntu 14.04.2 server download